Steam Jet Mill for Phytosterol

STEAM JET MILL for phytosterol is a clean, efficient, high-performance, high-yield, an advanced crusher model in pulverization, is very extensive, from a few triggered trace experiments, With a large production of hundreds of tons, Steam Jet Mill for phytosterol is narrow by it: the particle size distribution is narrow, the average particle size is fine; the powder is good, the product is purity; suitable for low melting point, thermal drugs; good sealavish, less pollution; Easy; crushing - mixing - dry online operations, etc. have been widely recognized by the company.

Steam Jet Mill for phytosterol production lines typically have pulverizer, bucket hoist, storage box, vibrating feeder, ultrafine mill, frequency classifier, cyclone powder collector, pulse dust removal system, high pressure Air blower, air compressor, electrical control system and other components. Eliminates the infrastructure construction link, saving overall production costs, reducing material consumption. In addition, crushing and grinding operations can also be completed, reducing equipment and minimizing cost investment.

Steam Jet Mill for PHYTOSTEROL has a specially designed high-pressure intake nozzle, which is contained in a particularly designed high-pressure intake nozzle, which is contained from the nozzle to form an ultrasonic air flow. Materials collide in the center of the high-speed airflow intersection, and it is pulverized in an instant. The pulverized particles rose to the grading chamber, and the qualified particles enter the cyclone separator with the gas, and finally obtain the desired product, the exhaust gas enters the dust collector.

The turbine grading system set in the classification room can obtain a powder of micrometers or even finer. When the pulverized material is pulverized in the pulverized chamber, the same particles at the edge of the turbine will be attached to the two different effort of the centrifuge field (i.e., centrifugal force and airflow resistance generated by turbine). When the particles are large, the centrifugal force is greater than the resistance, and the large particles fly toward the chamber pool wall along the turbine tangential direction, and then returned to the pulverizing chamber to be re-pulverized. When the particles are small, at this time, at this time is less than the resistance, the small particles enter the interior of the turbine with the rising airflow, and collectively collected by the cyclone to qualified products.


For the long-term \"health\" of the equipment, we need to take some steps to protect it again.

1. First, the gap of the hammer screen can be adjusted: the friction on the screen changes varies from the distance between the material and the screen, and the friction is different. Improve the hammer speed and hammer material efficiency by adjusting the hammer net gap. However, during the production process, the screens they use are different, the raw materials are different, the hammer screening gap needs to be adjusted; in the crusher, the crusher is not very good at the beginning, but after a period of time Work, the particles inside the crusher will also have a big change;In the bed parts, the hammer head is easily worn, and the gap between the hammer head and the screen is increased, and the yield is also reduced.

Of course, in order to test the yield of a crusher, for some of the raw materials, for some screen holes, in order to determine the appropriate hammer sieve gap and suction, the useful life of the screen and the hammer can be obtained in a short time. Very high grinding efficiency data. However, in the production of feed grinding, such specific measurement data, according to the operator's work experience, the technical content of the crusher itself is two things. People with enrichment of experience and labor experience also require higher operating costs. When the hammer is worn, the gap between the hammer and the sieve increases, the friction is reduced, and the abrasive efficiency is lowered.
2.Steam Jet Mill for phytosterol is mainly a renewal burr: mainly to rush the side hair of the screen into the inside, greatly increasing friction, but this method is not used for a long time. After the globi polishing, the efficiency is lowered. It lasts for 30 minutes to 1 hour.
3. Place the friction piece into Steam Jet Mill for phytosterol: The friction piece has the effect of the material ring, but the effect is limited. First, the teeth of the friction plate are in front of the hammer head, the friction surface is small, and the hammer is long-lasting; if the sieve area is too small, the output screen area will be reduced.
For any device, everyday maintenance can be performed, to ensure that the equipment can run for a long time, so daily is critical to Steam Jet Mill for Phytosterol.


ALPA Cobalt Solitrate STEAM JET MILL for PHYTOSTEROL Case Sharing:

A energy company is a professional lithium-ion power battery for new energy vehicles, and the storage capacity of lithium-ion batteries. Industrialization high-tech enterprises, the company actively responded to national policy calls, in order to promote new energy vehicles, the new energy vehicles rapidly, sustainable development, insist on the road to independent research and development, and have a core technical system that completely independent intellectual property rights, successfully developed There are many series of lithium-ion power battery batteries, which have been widely used in China's electric new energy vehicles, and market distribution has spread all over the country.

Case parameters:
Product particle size: D50: 15μm
Hour Yield: 600kg

Crushing equipment developed by ALPA technology has been applied in many actual engineering cases, and is based on the objective understanding of jet Technical provides basic information.