Air Classifier Mill for High Purity Silica

With the continuous increase in social needs, Air Classifier Mill for High Purity Silica continues to improve in terms of performance, finished product quality, service life, etc. A wide range of applications in many areas such as chemical, food, pesticides, cosmetics, dyes, coatings, and electrons.

In terms of airflow milling, it is important to understand its operational rules, which is very important because only familiarize the procedure, can operate correctly.
1. The operation rules of Air Classifier Mill for High Purity Silica are as follows: Prepare materials before the start of the production order, prepare materials. Complete the site to clean the grocery. Check whether the transportation pipes and auxiliary equipment, whether the pipelines are blocked, leak or poor sealing, whether the auxiliary equipment is intact, whether it works normally. Whether there is a phenomenon that the material is accumulated in the outer casing and the separator, if the accumulated material is required. Whether the bearing is lubricated, whether it is lubricated in an appropriate place. Check if all pipes, fastening bolts, washers, spindles, and instruments are intact, normal and flexible.
Second, Air Classifier Mill for High Purity Silica starts the motor, control the current and time at starting, so that the device can start running. When the equipment is operating normally, the feed speed can be adjusted according to the properties of the material. Uniform continuous feed should not be large or small, thereby affecting the separation effect of the grinding machine, making the machine easily malfunction. During operation, if an abnormality occurs, stop checking immediately before the failure continues.
Third, the main procedures of the closure and inspection of Air Classifier Mill for High Purity Silica are as follows: After the material in the grinding machine housing is completely pulverized, the feed should be stopped and turned off the motor. After the machine is idling for 3 minutes, press the stop button to stop the machine. When the machine is completely stopped, open the check door and check the wear of the vessel. Fill in the corresponding production record, update the device status flag, which is convenient for the next use.


AIR Classifier Mill for High Purity Silica's working principle consists of a grace machine, a cyclone separator, a dust collector, and a veneer. Under the pulverizing fan puller, the lower end of the gas pulverizer is moved upward to the hierarchical region, and the thickness and fine product are separated from the strong center of effort to the high-speed rotation grade turbine. The cyclonic separator or dust collector is collected by the grading wheel, and fine particles required to meet the particle size are collected, and the coarse particles are collected. The velocity of the entrained fine particles disappears and falls along the two towers of the cylinder wall. thickThe particles and fine particles are separated by strong purification of the two winds, and the fine particles rises twice as the grade region, and the crude particles fall to the discharge port.
Air Classifier Mill for High Purity Silica should maintain and maintain
1. Before using it, check all standard parts for all standard parts, and the belt is not tightened.

2, the spindle operation direction must conform to the direction of the arrow shown on the protective cover, otherwise it will damage the equipment, and may cause human damage.

3, check the electrical appliance is not intact.

4. Check the hardware such as metal-free materials in the equipment crushing room, otherwise it will damage the tool, affect the equipment operation.

5, the material must be checked before crushing, and there is no metal material hard article to be mixed to prevent crash or cause combustion.
6, the oil cup on the device should often be injected into the lubricant to ensure that the equipment is operating normally.
7. Stopping the feeding before the shutdown, if it does not continue to be used, clear the in the machine.
8. Check the tool with the screen on time is damaged. If it is damaged, it should be replaced first.
9. When using the timing, there is a small oscillation, so it is necessary to connect the handle to the handle to avoid accidents.

ALPA Pea Protein Air Classifier Mill for High Purity Silica Share: This customer is a food company in Russia. After looking for many powder equipment companies, they did not find the right equipment. It has been influenced by the company's production and operation, and finally I saw the ultrafine pulverization of pea protein before our website. Finally, through the incoming experiment, I finally determined the purchase of AIR Classifier Mill for Purity Silica.
Technical parameters:
finished particle size: 400 mesh
Production capacity: 1.5T

Today, Air Classifier Mill for High Purity Silica's knowledge, I will introduce you to here, think For more information, please continue to pay attention to our website.