Jet Mill of Feldspar

Many friends who want to produce industrialized must be unfamiliar with Jet Mill of Feldspar. Jet Mill of FeldSpar has a very convenient, crushing speed, and the quality of crushing products, is a very useful crushing machine.

When Jet Mill of FeldSPAR screen material, under the pressure of the rotating duct, the screen has good commonity. At the same time, under the gravity of the air blower, the screen collects the qualified material, and automatically discharges the material in the front cavity of the valve body by the unloading valve. The raw material powder driven by the compressed air is continuously supplied to the classifier without the need for rotating components. By accurate control of the airflow into three products: F fine powder, m powder and G coarse powder, and collected in subsequent cyclone dust collectors and dust collectors. The material is driven by the blower of the airflow pulverizer. The lower end of the classifier moves upward moves up to the hierarchical area, the strobe, the strongest centrifugal force generated by the high-speed rotation grading turbine. The fine particles that satisfy the particle size requirements are entered into the cyclone separator or dust collector by the gap of the graded wheel blades. After collecting, some of the thick particles of the fine particles disappear and drops along the cylinder wall to two air ports. The crude particles and fine particles are separated by strong purification of the two winds, and the fine particles rises twice as the grade region, and the crude particles fall to the discharge exit.

Next, we understand the working principle of the ultrafine pulverizer.
When working, the material to be pulverized from the feed hood on the side of the hood shell, relying on the grinding roller device suspended on the main plum flower frame, rotating around the vertical axis, and itself is rotated, due to rotation The role of the grinding roller is swing outward, pressing the mill, so that the shovel shovel is sent between the mill and the abrasive ring, and the purpose of the pulverized material is achieved due to rolling rolling of the grinding roller. Warlective process: After the material is ground, the fan blows the wind into the main casing, blows the powder, and is selected from the analyzer above the grinding chamber, and the fine material is refined into the grinding chamber. The style of constructing the wind flow into the cyclone collector, and after collecting the powder, it is the finished product.
The wind flow is reflected in the wind turbine in the upper end of the large cyclone collector, and the wind path is cycle, and in the negative pressure state, the air of the circulating wind turbine increases the exhaust gas pipeline between the flowers and the middle of the main unit. Small cyclone collector for purification treatment.

Do you know how to use Jet Mill of FeldSpar correctly? I hope the content below can help you.
1. Preparation before the pulverizer is started to check whether the host, joint, pipeline, and the valve are normal and working properly.
2, open the pulverizer

(1) Open the compressor power supply, dustpress pressure valve and the main air valve, open the power switch of the pulverizer, turn on the power switch.
(2) From scratch, gradually adjust to specified speedSpend.

(3) Open the fan, cyclone separator, dust removal and charger power, open the total power box, set the frequency of the inverter, and then start charging.
(4) The particle size of the finished product can be adjusted according to the frequency and bearing capacity of the grading wheel.
3, pulverizer shutdown sequence is: inverter - feeder - main valve compressor - Compressive plane impeller motor - cyclone material, dust removal switch - fan - General power supply air compressor.
4, eddy current pulverizer maintenance and maintenance

(1) Periodically lubricate the eddy current pulverizer, but the lubricating oil should not be too large to prevent too high of the bearing temperature.
(2) Check the wear of impeller, helical conveyors, and crushing nozzles.
(3) After pulverizing the material, the rubber powder should be removed to avoid clogging, thereby affecting the crushing effect.
(4) After the filter bag is filtered, it should be cleaned or replaced.
5, eddy current pulverizer precautions

(1) When the device is running, the unloading port cannot be reached, and the accident occurs.
(2) The rotational speed of the impeller should not exceed the specified requirements, otherwise the temperature is too high, the impeller and the electric chance are damaged.
(3) Regularly check the safety valve to ensure safety.

ALPA Trimel Cobalt Solites Jet Mill of FeldSPAR Case Sharing:
A new energy technology company is a lithium-ion power battery specializing in new energy vehicles, lithium-ion batteries and lithium ions with energy storage High-tech enterprises in the R \u0026 D and industrialization of battery key materials, take the lead in achieving large-capacity manganese lithium-ion batteries in scale production and marketization application of power battery companies.
Case parameters:
Product particle size: D50: 3-25UM
Hours Yield: 3-10kg

Users who want to view crusher related information can also log in to our website!