Fluidized Bed Jet Mill of Needle-Like Plaster

FLUIDIZED BED JET MILL of Needle-Like Plaster as a crushing main device, the role is also growing, in the industrial sector of metallurgy, mines, chemicals, cement, and has a large number of raw materials and reuse each year. The waste needs to be processed using a classifier. In the coking plant, sintering plants, ceramics factories, glass industries, powder metallurgy, etc., need to break the raw materials to the particle size required for the next job. In the chemical, power sector, the hierarchy, the raw material is broken, grind, increase the surface area of \u200b\u200bthe material, has created favorable conditions to shorten the chemical reaction of the material.

In terms of airflow milling, it is important to understand its operational rules, which is very important because only familiarize the procedure, can operate correctly.
1. The operating rules of the Fluidized Bed Jet Mill of Needle-Like Plaster are as follows: Prepare materials before the preparation of the production order is received. Complete the site to clean the grocery. Check whether the transportation pipes and auxiliary equipment, whether the pipelines are blocked, leak or poor sealing, whether the auxiliary equipment is intact, whether it works normally. Whether there is a phenomenon that the material is accumulated in the outer casing and the separator, if the accumulated material is required. Whether the bearing is lubricated, whether it is lubricated in an appropriate place. Check if all pipes, fastening bolts, washers, spindles, and instruments are intact, normal and flexible.
Second, Fluidized BED JET MILL OF NEEDLE-LIKE PLASTER starts the motor, control the current and time at starting, so that the device can start running. When the equipment is operating normally, the feed speed can be adjusted according to the properties of the material. Uniform continuous feed should not be large or small, thereby affecting the separation effect of the grinding machine, making the machine easily malfunction. During operation, if an abnormality occurs, stop checking immediately before the failure continues.

Third, the main procedures of the close and inspection of the Fluidized BED JET MILL OF NEEDLE-LIKE PLASTER are as follows: After the material in the grinding machine housing is completely pulverized, it should stop the feed and turn off the motor. After the machine is idling for 3 minutes, press the stop button to stop the machine. When the machine is completely stopped, open the check door and check the wear of the vessel. Fill in the corresponding production record, update the device status flag, which is convenient for the next use.


Let's take a look at how to extend the usage time of Fluidized Bed Jet Mill of Needle-Like Plaster:
1. Strictly follow the operating procedures;

2, easy Damaged parts should pay attention to time check, andReplacement.

3, the device body has no rotating parts, which is not affected by the lifetime of the bearing. However, due to the difference in powder hardness, the degree of wear is different, especially the wear of the hierarchy knife tip, our company's body part is made of special material, the tip service life is at least more than one year, the knife tip is more than 1 cm or more It will affect the grading accuracy, in order to avoid affecting product quality, it is recommended to contact us to replace the knife pointer;
4. It is recommended to use a long filter device to improve equipment stability, and ensure grading precision.
Fluidized Bed Jet Mill of Needle-Like Plaster is a more accurate mechanical, in the daily use and maintenance process, some details still require the operator's attention. In order to improve the pulverization efficiency of gas flow mill, it is necessary to check whether the feedstock meets the requirements before the production, and the foreign matter is strictly prohibited into the raw material.
In production, a certain number of materials must be maintained in the airflow grinding chamber. In the case where the flow rate of the pulverized gas is not changed, the material in the grinding cavity is large, the gradient current is large, and the material is small in the grinding cavity, the gradient current is small.
In addition, the feeding speed must remain uniform and stable, don't be too fast or too slow.

If the feeding speed is too fast, the device will overload.

Regular maintenance equipment, often check whether the air supply pressure meets the pressure required, and the gas flow grinding motor, after 3,000 hours of operation, or long-term shutdown and long-term storage, should be cleaned in a gas flow grinder nozzle and grinding The inner wall of the cavity and attached to the material grading portion to prevent the effect of gas flow grinding on the grinding effect.


ALPA Light Bagne Fluidized Bed Jet Mill of Needle-Like Plaster Case Sharing: The customer is a device company, focusing cement, mine, chemical, electric power, metallurgy, etc., mainly engaged These industries are equipped with equipment, the customer needs to support its customers more suitable airflow classification equipment, after many exam, I chose our ALPA air classifier. Buy two devices. Product particle size: D80: 15μm hour yield: two 15t / h.
Our AlPA classifier can support ball mills, vertical grinding, Raymond mill, mechanical mill, etc., welcome customers to visit, incompetent experiments.

Shan dong alpa mainly engaged in the production and development and service of Fluidized Bed Jet Mill of Needle-Like Plaster product technology, welcome to come to consult. With good quality and service, affordable prices, customer-oriented attitudes provide airflow crushing products and services.