Air Classifier Mill for Gasified Fly Ash

Air Classifier Mill for Gasified Fly Ash is one of the common ultra-fine pulverization methods, widely used in ultra-fine pulverization or fine pulverization of materials such as non-metallic mine, chemical, chemical, metallurgical and other industrial materials, product particle size, particle size distribution Narrow, smooth surface surface, particle rules, high purity, high activity.

Which factors affect the performance parameters used by Air Classifier Mill for Gasified Fly ASH?

The following is a detailed description:

1. Feed particle size control

Most AIR Classifier Mill for Gasified Fly ASH has a certain upper limit requirement for feed particle size. After entering the pulverization cavity, it can be sufficiently accelerated before collision and crushing with other particles. It is difficult to completely accelerate after large particles enter the pulverized cavity, which will allow them to stay in the machine too long, resulting in too high energy consumption. Therefore, in large-scale production of ultrafine powder, it is an effective way to pre-ground the raw material of the particle size is an effective pathway for energy saving.
2. Working medium

Currently, the working medium of Air Classifier Mill for Gasified Fly ASH is mainly compressed, superheated steam, inert gas, and the like. The choice of working fluid has a certain impact on crushing effects and economics. Superheated steam is superior to air in fluidity and critical flow rates to achieve higher flow rates and uniform flow fields. However, using superheated steam as a working fluid, it must be ensured that it is still in an overheating state before entering the product capture device, otherwise the material is condensed.
3. Feeding speed

Feeding speed is an important parameter reflecting gas flow grinding production capacity. During the pulverization process, the optimum ratio of the intake flow rate and the feed speed is the key to improving the crushing efficiency. In general, under certain intake flow conditions, the feed speed is proportional to the particle size of the product. However, the feeding speed is too fast, which will increase the particle density, mutual interference, disadvantage of the particles, and difficult to achieve the sufficient and effective collision between particles, affect the crushing effect; although the feed speed is too slow, the particles stay in the crush area The time can be extended, which will reduce the particle density, reduce the collision rate, resulting in a decrease in production capacity and an increase in unit production energy consumption.
4. Granular limit

Air Classifier Mill for Gasified Fly ASH In the pulverization process, as the material particle size is reduced, the crystallization and intensity of the material increases. After reaching a certain degree, the particle size of the material is no longer reduced or reduced, that is, the crushing limit of the material is reached.At this time, the material specific surface area increases, the surface activity of the particles, the particle agglomeration and grinding are in a dynamic equilibrium state, even if the grinding time is prolonged, it is difficult to further reduce the particle size of the material.



AIR Classifier Mill for Gasified Fly ASH Working Principles: Handle the material from the feeding of the material is evenly fed into the pulverized mouth, and under the action of the fixed knife and rotary knife, All kinds of straw cut into small segments, then enter the crushing room, under the strong hit of the hammer placed at high speed, the material is rapidly pulverized, due to the large amount of wind pressure in the centrifugal force and the built-in fan, under the negative pressure of the underclocking chamber, was pulverized The material is filled into the lower chamber by the screen hole, and is sent from the wind pressure transfer pipe to the aggregate room.
Installation, operation and maintenance is three important factors using Air Classifier Mill for Gasified Fly ASH. The wear and consumption of each operation has always been a key factor in each startup operation. In order to use the airflow pulverizer for a long time, please adjust the open mode. Boot is a standard, for the first time to contact and use this kind of equipment, it is always a very strange state. In fact, it is very simple, the best way is to familiarize yourself with the consumer content on the instructions or have no use value. Timely specification and familiar. After each startup, check the airflow pulverizer in time to develop good usage habits. In the future, we don't need to pay attention to and familiarize.
The airflow pulverizer has improved and improved from the design and component combination, gave us a lot of help. It is good quality, but it is also declined for a long time without maintenance and maintenance. Check the operating components, electrical components, and transmission. Once an abnormality occurs, please repair it in time, without a fault, gas mill, prevent accidents.

AlPa Kaolin Air Classifier Mill for Gasified Fly Ash case Sharing: This customer is a Kaolin Powder company in India, which requires a grading equipment to select the Kaolin soil ultrafine powder, and investigate a lot of companies. Did not find a suitable. Finally, our AlPA meets the customer needs for the classifier equipment provided. The set of equipment has reached 4T per hour.

The Shan Dong Alpa is a scientific and private enterprise producing various airflow pulverities, integrating development, manufacturing, and application. The main product model has airflow pulverizer, airflow mill, pharmaceutical gas flow pulverizer, disc air pulverizer, eddy current pulverizer.